schorsch312
Routinier
Hi,
Ich habe per emerge -C alsa-driver selbigen deinstalliert. Jetzt bekomme ich jede Menge Fehlermeldungen beim Start.
1.) could not open System.map no such file or directory
2.) irgendwas mit modprobe could not load module
3.) irgend was mit could not fin alsa-driver see dmesg
Die dmesg ist im Anhang.
Ich finde leider keine boot.log, um es genau nach yu schauen.
Wie kann ich denn jetzt den alsa-driver entgueltig deinstallieren, um ihn in den Kernel zu verbannen?
Gruss, Georg
Bootdata ok (command line is root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/sda3 udev vga=791 video=vesafb:mtrr:3,ywrap,1280x1024,16)
Linux version 2.6.18-gentoo-r1 (root@livecd) (gcc version 4.1.1 (Gentoo 4.1.1)) #1 SMP Sat Oct 21 18:52:31 CEST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ffb0000 (usable)
BIOS-e820: 000000003ffb0000 - 000000003ffc0000 (ACPI data)
BIOS-e820: 000000003ffc0000 - 000000003fff0000 (ACPI NVS)
BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000fa7c0
ACPI: RSDT (v001 A M I OEMRSDT 0x05000519 MSFT 0x00000097) @ 0x000000003ffb0000
ACPI: FADT (v001 A M I OEMFACP 0x05000519 MSFT 0x00000097) @ 0x000000003ffb0200
ACPI: MADT (v001 A M I OEMAPIC 0x05000519 MSFT 0x00000097) @ 0x000000003ffb0390
ACPI: OEMB (v001 A M I OEMBIOS 0x05000519 MSFT 0x00000097) @ 0x000000003ffc0040
ACPI: DSDT (v001 A0036 A0036001 0x00000001 MSFT 0x0100000d) @ 0x0000000000000000
Scanning NUMA topology in Northbridge 24
Number of nodes 1
Node 0 MemBase 0000000000000000 Limit 000000003ffb0000
NUMA: Using 63 for the hash shift.
Using node hash shift of 63
Bootmem setup node 0 0000000000000000-000000003ffb0000
On node 0 totalpages: 257252
DMA zone: 2810 pages, LIFO batch:0
DMA32 zone: 254442 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:15 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bf780000)
Built 1 zonelists. Total pages: 257252
Kernel command line: root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/sda3 udev vga=791 video=vesafb:mtrr:3,ywrap,1280x1024,16
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer.
time.c: Detected 2002.581 MHz processor.
Speakup v-2.00 CVS: Tue Aug 1 11:16:55 EDT 2006 : initialized
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Checking aperture...
CPU 0: aperture @ dc000000 size 64 MB
Memory: 1025148k/1048256k available (2725k kernel code, 22720k reserved, 1056k data, 228k init)
Calibrating delay using timer specific routine.. 4009.96 BogoMIPS (lpj=8019923)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0/0 -> Node 0
SMP alternatives: switching to UP code
Freeing SMP alternatives: 32k freed
ACPI: Core revision 20060707
Using local APIC timer interrupts.
result 12516148
Detected 12.516 MHz APIC timer.
Brought up 1 CPUs
testing NMI watchdog ... OK.
migration_cost=0
checking if image is initramfs... it is
Freeing initrd memory: 2202k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: enabled onboard AC97/MC97 devices
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 64M @ 0xdc000000
PCI-DMA: Disabling IOMMU.
pnp: 00:08: ioport range 0x680-0x6ff has been reserved
pnp: 00:08: ioport range 0x290-0x297 has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: faf00000-fbffffff
PREFETCH window: e0000000-f9ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1161605974.428:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
squashfs: version 3.1 (2006/08/19) Phillip Lougher
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
0000:00:10.4 EHCI: BIOS handoff failed (BIOS bug ?) 01010001
initialized device: /dev/synth, node ( MAJOR 10, MINOR 25 )
Linux agpgart interface v0.101 (c) Dave Jones
vesafb: framebuffer at 0xe0000000, mapped to 0xffffc20000080000, using 3072k, total 131072k
vesafb: mode is 1024x768x16, linelength=2048, pages=1
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
PNP: PS/2 Controller [PNP0303
S2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 169
PCI: VIA IRQ fixup for 0000:00:0f.1, from 255 to 9
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb
MA
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hddMA
Probing IDE interface ide0...
input: AT Translated Set 2 keyboard as /class/input/input0
hdb: Maxtor 6Y080L0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdd: BENQ DVD DD DW1620, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hdb: max request size: 128KiB
hdb: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(133)
hdb: cache flushes supported
hdb: hdb1 hdb2 < hdb5 >
hdd: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 228k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
GSI 17 sharing vector 0xB1 and IRQ 17
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 177
PCI: VIA IRQ fixup for 0000:00:10.4, from 5 to 1
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 177, io mem 0xfae00000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
usb 1-6: new high speed USB device using ehci_hcd and address 3
usb 1-6: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 177
PCI: VIA IRQ fixup for 0000:00:10.0, from 11 to 1
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 177, io base 0x0000d400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 177
PCI: VIA IRQ fixup for 0000:00:10.1, from 11 to 1
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 177, io base 0x0000d800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2 -> GSI 21 (level, low) -> IRQ 177
PCI: VIA IRQ fixup for 0000:00:10.2, from 10 to 1
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 177, io base 0x0000e000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3 -> GSI 21 (level, low) -> IRQ 177
PCI: VIA IRQ fixup for 0000:00:10.3, from 10 to 1
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 177, io base 0x0000e400
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
sl811: driver sl811-hcd, 19 May 2005
ieee1394: Initialized config rom entry `ip1394'
GSI 18 sharing vector 0xB9 and IRQ 18
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 185
PCI: VIA IRQ fixup for 0000:00:07.0, from 11 to 9
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[185] MMIO=[fa800000-fa8007ff] Max Packet=[2048] IR/IT contexts=[4/8]
usb 3-1: new low speed USB device using uhci_hcd and address 2
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
libata version 2.00 loaded.
sata_promise 0000:00:08.0: version 1.04
GSI 19 sharing vector 0xC1 and IRQ 19
ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 18 (level, low) -> IRQ 193
sata_promise PATA port found
ata1: SATA max UDMA/133 cmd 0xFFFFC20000066200 ctl 0xFFFFC20000066238 bmdma 0x0 irq 193
ata2: SATA max UDMA/133 cmd 0xFFFFC20000066280 ctl 0xFFFFC200000662B8 bmdma 0x0 irq 193
ata3: PATA max UDMA/133 cmd 0xFFFFC20000066300 ctl 0xFFFFC20000066338 bmdma 0x0 irq 193
scsi1 : sata_promise
usb 3-1: configuration #1 chosen from 1 choice
input: Logitech USB Receiver as /class/input/input1
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:10.1-1
ata1: SATA link down (SStatus 0 SControl 0)
scsi2 : sata_promise
ata2: SATA link down (SStatus 0 SControl 300)
scsi3 : sata_promise
ATA: abnormal status 0x8 on port 0xFFFFC2000006631C
ata3: disabling port
sata_via 0000:00:0f.0: version 2.0
ACPI: PCI Interrupt 0000:00:0f.0 -> GSI 20 (level, low) -> IRQ 169
PCI: VIA IRQ fixup for 0000:00:0f.0, from 10 to 9
sata_via 0000:00:0f.0: routed to hard irq line 9
ata4: SATA max UDMA/133 cmd 0xD000 ctl 0xC802 bmdma 0xB800 irq 169
ata5: SATA max UDMA/133 cmd 0xC400 ctl 0xC002 bmdma 0xB808 irq 169
scsi4 : sata_via
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATA-7, max UDMA7, 488397168 sectors: LBA48 NCQ (depth 0/32)
ata4.00: ata4: dev 0 multi count 16
ata4.00: configured for UDMA/133
scsi5 : sata_via
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d800006ee377]
ata5: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
ATA: abnormal status 0x7F on port 0xC407
Vendor: ATA Model: SAMSUNG SP2504C Rev: VT10
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4
sd 4:0:0:0: Attached scsi disk sda
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: **********
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
JFS: nTxBlock = 8028, nTxLock = 64225
ReiserFS: sda3: found reiserfs format "3.6" with standard journal
Vendor: Generic Model: USB SD Reader Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 00
sd 0:0:0:0: Attached scsi removable disk sdb
Vendor: Generic Model: USB CF Reader Rev: 1.01
Type: Direct-Access ANSI SCSI revision: 00
sd 0:0:0:1: Attached scsi removable disk sdc
Vendor: Generic Model: USB SM Reader Rev: 1.02
Type: Direct-Access ANSI SCSI revision: 00
sd 0:0:0:2: Attached scsi removable disk sdd
Vendor: Generic Model: USB MS Reader Rev: 1.03
Type: Direct-Access ANSI SCSI revision: 00
sd 0:0:0:3: Attached scsi removable disk sde
usb-storage: device scan complete
ReiserFS: sda3: using ordered data mode
ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda3: checking transaction log (sda3)
ReiserFS: sda3: Using r5 hash to sort names
ReiserFS: sda1: found reiserfs format "3.6" with standard journal
ReiserFS: sda1: using ordered data mode
ReiserFS: sda1: journal params: device sda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda1: checking transaction log (sda1)
ReiserFS: sda1: Using r5 hash to sort names
ReiserFS: sda4: found reiserfs format "3.6" with standard journal
ReiserFS: sda4: using ordered data mode
ReiserFS: sda4: journal params: device sda4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda4: checking transaction log (sda4)
ReiserFS: sda4: Using r5 hash to sort names
Adding 1004052k swap on /dev/sda2. Priority:-1 extents:1 across:1004052k
Real Time Clock Driver v1.12ac
Ich habe per emerge -C alsa-driver selbigen deinstalliert. Jetzt bekomme ich jede Menge Fehlermeldungen beim Start.
1.) could not open System.map no such file or directory
2.) irgendwas mit modprobe could not load module
3.) irgend was mit could not fin alsa-driver see dmesg
Die dmesg ist im Anhang.
Ich finde leider keine boot.log, um es genau nach yu schauen.
Wie kann ich denn jetzt den alsa-driver entgueltig deinstallieren, um ihn in den Kernel zu verbannen?
Gruss, Georg
Bootdata ok (command line is root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/sda3 udev vga=791 video=vesafb:mtrr:3,ywrap,1280x1024,16)
Linux version 2.6.18-gentoo-r1 (root@livecd) (gcc version 4.1.1 (Gentoo 4.1.1)) #1 SMP Sat Oct 21 18:52:31 CEST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ffb0000 (usable)
BIOS-e820: 000000003ffb0000 - 000000003ffc0000 (ACPI data)
BIOS-e820: 000000003ffc0000 - 000000003fff0000 (ACPI NVS)
BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000fa7c0
ACPI: RSDT (v001 A M I OEMRSDT 0x05000519 MSFT 0x00000097) @ 0x000000003ffb0000
ACPI: FADT (v001 A M I OEMFACP 0x05000519 MSFT 0x00000097) @ 0x000000003ffb0200
ACPI: MADT (v001 A M I OEMAPIC 0x05000519 MSFT 0x00000097) @ 0x000000003ffb0390
ACPI: OEMB (v001 A M I OEMBIOS 0x05000519 MSFT 0x00000097) @ 0x000000003ffc0040
ACPI: DSDT (v001 A0036 A0036001 0x00000001 MSFT 0x0100000d) @ 0x0000000000000000
Scanning NUMA topology in Northbridge 24
Number of nodes 1
Node 0 MemBase 0000000000000000 Limit 000000003ffb0000
NUMA: Using 63 for the hash shift.
Using node hash shift of 63
Bootmem setup node 0 0000000000000000-000000003ffb0000
On node 0 totalpages: 257252
DMA zone: 2810 pages, LIFO batch:0
DMA32 zone: 254442 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:15 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bf780000)
Built 1 zonelists. Total pages: 257252
Kernel command line: root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/sda3 udev vga=791 video=vesafb:mtrr:3,ywrap,1280x1024,16
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer.
time.c: Detected 2002.581 MHz processor.
Speakup v-2.00 CVS: Tue Aug 1 11:16:55 EDT 2006 : initialized
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Checking aperture...
CPU 0: aperture @ dc000000 size 64 MB
Memory: 1025148k/1048256k available (2725k kernel code, 22720k reserved, 1056k data, 228k init)
Calibrating delay using timer specific routine.. 4009.96 BogoMIPS (lpj=8019923)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0/0 -> Node 0
SMP alternatives: switching to UP code
Freeing SMP alternatives: 32k freed
ACPI: Core revision 20060707
Using local APIC timer interrupts.
result 12516148
Detected 12.516 MHz APIC timer.
Brought up 1 CPUs
testing NMI watchdog ... OK.
migration_cost=0
checking if image is initramfs... it is
Freeing initrd memory: 2202k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: enabled onboard AC97/MC97 devices
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 64M @ 0xdc000000
PCI-DMA: Disabling IOMMU.
pnp: 00:08: ioport range 0x680-0x6ff has been reserved
pnp: 00:08: ioport range 0x290-0x297 has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: faf00000-fbffffff
PREFETCH window: e0000000-f9ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1161605974.428:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
squashfs: version 3.1 (2006/08/19) Phillip Lougher
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
0000:00:10.4 EHCI: BIOS handoff failed (BIOS bug ?) 01010001
initialized device: /dev/synth, node ( MAJOR 10, MINOR 25 )
Linux agpgart interface v0.101 (c) Dave Jones
vesafb: framebuffer at 0xe0000000, mapped to 0xffffc20000080000, using 3072k, total 131072k
vesafb: mode is 1024x768x16, linelength=2048, pages=1
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
PNP: PS/2 Controller [PNP0303
S2K] at 0x60,0x64 irq 1PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 169
PCI: VIA IRQ fixup for 0000:00:0f.1, from 255 to 9
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb
MAide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd
MAProbing IDE interface ide0...
input: AT Translated Set 2 keyboard as /class/input/input0
hdb: Maxtor 6Y080L0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdd: BENQ DVD DD DW1620, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hdb: max request size: 128KiB
hdb: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(133)
hdb: cache flushes supported
hdb: hdb1 hdb2 < hdb5 >
hdd: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 228k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
GSI 17 sharing vector 0xB1 and IRQ 17
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 177
PCI: VIA IRQ fixup for 0000:00:10.4, from 5 to 1
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 177, io mem 0xfae00000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
usb 1-6: new high speed USB device using ehci_hcd and address 3
usb 1-6: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 177
PCI: VIA IRQ fixup for 0000:00:10.0, from 11 to 1
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 177, io base 0x0000d400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 177
PCI: VIA IRQ fixup for 0000:00:10.1, from 11 to 1
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 177, io base 0x0000d800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2 -> GSI 21 (level, low) -> IRQ 177
PCI: VIA IRQ fixup for 0000:00:10.2, from 10 to 1
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 177, io base 0x0000e000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3 -> GSI 21 (level, low) -> IRQ 177
PCI: VIA IRQ fixup for 0000:00:10.3, from 10 to 1
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 177, io base 0x0000e400
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
sl811: driver sl811-hcd, 19 May 2005
ieee1394: Initialized config rom entry `ip1394'
GSI 18 sharing vector 0xB9 and IRQ 18
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 185
PCI: VIA IRQ fixup for 0000:00:07.0, from 11 to 9
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[185] MMIO=[fa800000-fa8007ff] Max Packet=[2048] IR/IT contexts=[4/8]
usb 3-1: new low speed USB device using uhci_hcd and address 2
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
libata version 2.00 loaded.
sata_promise 0000:00:08.0: version 1.04
GSI 19 sharing vector 0xC1 and IRQ 19
ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 18 (level, low) -> IRQ 193
sata_promise PATA port found
ata1: SATA max UDMA/133 cmd 0xFFFFC20000066200 ctl 0xFFFFC20000066238 bmdma 0x0 irq 193
ata2: SATA max UDMA/133 cmd 0xFFFFC20000066280 ctl 0xFFFFC200000662B8 bmdma 0x0 irq 193
ata3: PATA max UDMA/133 cmd 0xFFFFC20000066300 ctl 0xFFFFC20000066338 bmdma 0x0 irq 193
scsi1 : sata_promise
usb 3-1: configuration #1 chosen from 1 choice
input: Logitech USB Receiver as /class/input/input1
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:10.1-1
ata1: SATA link down (SStatus 0 SControl 0)
scsi2 : sata_promise
ata2: SATA link down (SStatus 0 SControl 300)
scsi3 : sata_promise
ATA: abnormal status 0x8 on port 0xFFFFC2000006631C
ata3: disabling port
sata_via 0000:00:0f.0: version 2.0
ACPI: PCI Interrupt 0000:00:0f.0 -> GSI 20 (level, low) -> IRQ 169
PCI: VIA IRQ fixup for 0000:00:0f.0, from 10 to 9
sata_via 0000:00:0f.0: routed to hard irq line 9
ata4: SATA max UDMA/133 cmd 0xD000 ctl 0xC802 bmdma 0xB800 irq 169
ata5: SATA max UDMA/133 cmd 0xC400 ctl 0xC002 bmdma 0xB808 irq 169
scsi4 : sata_via
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATA-7, max UDMA7, 488397168 sectors: LBA48 NCQ (depth 0/32)
ata4.00: ata4: dev 0 multi count 16
ata4.00: configured for UDMA/133
scsi5 : sata_via
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d800006ee377]
ata5: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
ATA: abnormal status 0x7F on port 0xC407
Vendor: ATA Model: SAMSUNG SP2504C Rev: VT10
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4
sd 4:0:0:0: Attached scsi disk sda
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: **********
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
JFS: nTxBlock = 8028, nTxLock = 64225
ReiserFS: sda3: found reiserfs format "3.6" with standard journal
Vendor: Generic Model: USB SD Reader Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 00
sd 0:0:0:0: Attached scsi removable disk sdb
Vendor: Generic Model: USB CF Reader Rev: 1.01
Type: Direct-Access ANSI SCSI revision: 00
sd 0:0:0:1: Attached scsi removable disk sdc
Vendor: Generic Model: USB SM Reader Rev: 1.02
Type: Direct-Access ANSI SCSI revision: 00
sd 0:0:0:2: Attached scsi removable disk sdd
Vendor: Generic Model: USB MS Reader Rev: 1.03
Type: Direct-Access ANSI SCSI revision: 00
sd 0:0:0:3: Attached scsi removable disk sde
usb-storage: device scan complete
ReiserFS: sda3: using ordered data mode
ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda3: checking transaction log (sda3)
ReiserFS: sda3: Using r5 hash to sort names
ReiserFS: sda1: found reiserfs format "3.6" with standard journal
ReiserFS: sda1: using ordered data mode
ReiserFS: sda1: journal params: device sda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda1: checking transaction log (sda1)
ReiserFS: sda1: Using r5 hash to sort names
ReiserFS: sda4: found reiserfs format "3.6" with standard journal
ReiserFS: sda4: using ordered data mode
ReiserFS: sda4: journal params: device sda4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda4: checking transaction log (sda4)
ReiserFS: sda4: Using r5 hash to sort names
Adding 1004052k swap on /dev/sda2. Priority:-1 extents:1 across:1004052k
Real Time Clock Driver v1.12ac
